Search the site
In April 2016 Manchester eScholar was replaced by the University of Manchester’s new Research Information Management System, Pure. In the autumn the University’s research outputs will be available to search and browse via a new Research Portal. Until then the University’s full publication record can be accessed via a temporary portal and the old eScholar content is available to search and browse via this archive.

# Simulation of 3D Sensors

[Thesis]. Manchester, UK: The University of Manchester; 2013.

## Abstract

The Large Hadron Collider (LHC) at CERN has the highest energy and luminosity in the world. Radiation hardness is then a critical requirement for the inner tracker design. The inner tracker is important for identifying heavy quarks using high spatial precision detectors. Silicon detectors are now the primary technology for this application.3D silicon sensors use a novel technology with penetrating electrodes and have excellent radiation hardness by design. It overcomes the signal loss with a low operation voltage by reducing the collection length compared to the current planar technology used in the ATLAS pixel detector.The ATLAS insertable B-layer (IBL) is an upgrade to improve tracking resolution of the inner tracker and will be installed in 2013. It will be composed of 75\% planar sensors and 25\% 3D sensors in the large-$\eta$ region. It is important to simulate the IBL tracking performance and to have a valid model for 3D sensors.This thesis investigated the experimental data for heavily irradiated planar strip sensors and 3D sensors to develop a device simulator, in which impact ionisation has to be included. The modelling has found that the radiation induced effective doping concentration has two linear regimes with a smaller growth rate at high fluences. This shows the possibility to operate silicon sensors with a higher irradiation level. %Avalanche effects have to be included in the device simulation.The signal efficiency of each pixel is the basis to simulate the whole IBL response. A model and a code were developed to calculate the induced signal from electron-hole pairs generated by the traversing charge particles. This results in a 2D efficiency map used as an input of the 3D digitiser for the Geant4 simulation. This map was adopted by the IBL software team for the whole tracker simulation and has been validated by the test beam data.

## Keyword(s)

Type of resource:
Content type:
Form of thesis:
Type of submission:
Thesis title:
Degree type:
Doctor of Philosophy
Degree programme:
PhD Physics
Publication date:
Institution:
Location:
Manchester, UK
Total pages:
204
Abstract:
The Large Hadron Collider (LHC) at CERN has the highest energy and luminosity in the world. Radiation hardness is then a critical requirement for the inner tracker design. The inner tracker is important for identifying heavy quarks using high spatial precision detectors. Silicon detectors are now the primary technology for this application.3D silicon sensors use a novel technology with penetrating electrodes and have excellent radiation hardness by design. It overcomes the signal loss with a low operation voltage by reducing the collection length compared to the current planar technology used in the ATLAS pixel detector.The ATLAS insertable B-layer (IBL) is an upgrade to improve tracking resolution of the inner tracker and will be installed in 2013. It will be composed of 75\% planar sensors and 25\% 3D sensors in the large-$\eta$ region. It is important to simulate the IBL tracking performance and to have a valid model for 3D sensors.This thesis investigated the experimental data for heavily irradiated planar strip sensors and 3D sensors to develop a device simulator, in which impact ionisation has to be included. The modelling has found that the radiation induced effective doping concentration has two linear regimes with a smaller growth rate at high fluences. This shows the possibility to operate silicon sensors with a higher irradiation level. %Avalanche effects have to be included in the device simulation.The signal efficiency of each pixel is the basis to simulate the whole IBL response. A model and a code were developed to calculate the induced signal from electron-hole pairs generated by the traversing charge particles. This results in a 2D efficiency map used as an input of the 3D digitiser for the Geant4 simulation. This map was adopted by the IBL software team for the whole tracker simulation and has been validated by the test beam data.
Keyword(s):
Thesis main supervisor(s):
Degree grantor:
Language:
en

University researcher(s):

Manchester eScholar ID:
uk-ac-man-scw:211707
Created by:
Lai, Ching-Hung
Created:
26th October, 2013, 04:54:14